Bảng Mạch Phát Triển Attiny Màu Đen Cho Arduino Iic I2c Usb Attiny45
3 Đánh Giá
5 Đã Bán
35
31.100 đ
Xem sản phẩm trên ShopeeQuốc tế
thứ năm 29/04/2021 lúc 08:48 CH
Usb:
-support arduino ide 1.0+(osx/windows/linux).
-power supply via usb or external power supply or 7-16 v to 5 v (automatic selection).
-150 ma 5 v ballast on board.
-built-in-usb and serial debugging functions.
5. 6 i/o pins (2 will notify usb only if your program communicates proactively via usb or you can use all 6 if you program via usb).
6.8 k flash memory (approximately 6 k after booting the loader).
7. I2c and spi (relative to usu).
8. Pwm on 3 pins (software pwm may be more).
9. On 4 pins of adc.
-power supply led and test/state indicator lamp.
Specifications:
-support arduino ide 1.0+(osx/win/linux).
-power supply via usb or external power supply-5v or 7-16v (automatic selection).
-150ma 5v regulator on board.
-built-in usb (and serial debugging).
5. 6 i/o pins (only 2 are used for usb if your program communicates proactively via usb, or all 6 can be used even through usb programming).
6. 8k flash memory (approximately 6k after booting the loader).
7. I2c and spi (relative to usu).
8. Pwm on 3 pins (software pwm may be more).
9. Adc on 4 pins.
Black digispark usb development board
Digispark is a attiny85-based microcontroller development board similar to atliney85, but cheaper, smaller and less functional.Digispark, with a large number of protective covers, can expand its functionality and the ability to use familiar ide, is a good way to jump into electronic products, which are perfect for large or over-large electronics.
Digispark was fully assembled at the time of its departure, except for the two welded joints attached.
The specifications are as follows:
Support ide 1.0+(osx/win/linux)
Power supply via usb or external power supply-5v or 7-35v (recommendation 12v or lower, automatic selection)
Plate 500ma 5v regulator
Built-in usb
6 i/o pins (2 for usb only when programs communicate proactively via usb, or all 6 for usb programming)
8k flash memory (boot loader after about 6k)
I2c and spi (for osi)
3 pwm on pin (software pwm may be more)
4 pin adc
Power supply led and test/state led
Attiny85-20pu dip-8 feet straight plug
Development programming board attiny13a/attiny25/attiny45/attiny85 removable development programming board
Factory direct marketing programming is convenient and fast
Attiny13a/attiny25/attiny45/attiny85 et al.
Note: when out of the factory, do not bring attiny microcontroller chip, need chip, please ask yourself to buy it.
Note: no technical support is available for the board adapter
-support arduino ide 1.0+(osx/windows/linux).
-power supply via usb or external power supply or 7-16 v to 5 v (automatic selection).
-150 ma 5 v ballast on board.
-built-in-usb and serial debugging functions.
5. 6 i/o pins (2 will notify usb only if your program communicates proactively via usb or you can use all 6 if you program via usb).
6.8 k flash memory (approximately 6 k after booting the loader).
7. I2c and spi (relative to usu).
8. Pwm on 3 pins (software pwm may be more).
9. On 4 pins of adc.
-power supply led and test/state indicator lamp.
Specifications:
-support arduino ide 1.0+(osx/win/linux).
-power supply via usb or external power supply-5v or 7-16v (automatic selection).
-150ma 5v regulator on board.
-built-in usb (and serial debugging).
5. 6 i/o pins (only 2 are used for usb if your program communicates proactively via usb, or all 6 can be used even through usb programming).
6. 8k flash memory (approximately 6k after booting the loader).
7. I2c and spi (relative to usu).
8. Pwm on 3 pins (software pwm may be more).
9. Adc on 4 pins.
Black digispark usb development board
Digispark is a attiny85-based microcontroller development board similar to atliney85, but cheaper, smaller and less functional.Digispark, with a large number of protective covers, can expand its functionality and the ability to use familiar ide, is a good way to jump into electronic products, which are perfect for large or over-large electronics.
Digispark was fully assembled at the time of its departure, except for the two welded joints attached.
The specifications are as follows:
Support ide 1.0+(osx/win/linux)
Power supply via usb or external power supply-5v or 7-35v (recommendation 12v or lower, automatic selection)
Plate 500ma 5v regulator
Built-in usb
6 i/o pins (2 for usb only when programs communicate proactively via usb, or all 6 for usb programming)
8k flash memory (boot loader after about 6k)
I2c and spi (for osi)
3 pwm on pin (software pwm may be more)
4 pin adc
Power supply led and test/state led
Attiny85-20pu dip-8 feet straight plug
Development programming board attiny13a/attiny25/attiny45/attiny85 removable development programming board
Factory direct marketing programming is convenient and fast
Attiny13a/attiny25/attiny45/attiny85 et al.
Note: when out of the factory, do not bring attiny microcontroller chip, need chip, please ask yourself to buy it.
Note: no technical support is available for the board adapter